A hinge is a mechanical bearing that connects two solid objects, typically allowing only a limited angle of rotation between them. Two objects connected by an ideal hinge rotate relative to each other about a fixed axis of rotation, with all other translations or rotations prevented; thus a hinge has one degree of freedom. Hinges may be made of Flexure bearing or moving components. In biology, many function as hinges, such as the elbow joint.
History
Ancient remains of stone, marble, wood, and bronze hinges have been found. Some date back to at least
Ancient Egypt, although it is nearly impossible to pinpoint exactly where and when the first hinges were used.
In Ancient Rome, hinges were called and gave name to the goddess Cardea and the main street Cardo. This name cardō lives on figuratively today as "the chief thing (on which something turns or depends)" in words such as .
According to the Oxford English Dictionary, the English word hinge is related to .
Door hinges
- Barrel hinge
- A barrel hinge consists of a sectional barrel (the knuckle) secured by a pivot. A barrel is simply a hollow cylinder. The vast majority of hinges operate on the barrel principle.
- Butt hinge / Mortise hinge
- Any hinge designed to be set into a door frame or door is considered a butt hinge or mortise hinge. A hinge can also be made as a half-mortise, where only one half is mortised and the other is not. Most mortise hinges are also barrel hinges because of how they pivot (i.e., a pair of leaves secured to each other by knuckles through which runs a pin).
- Butterfly / Parliament (UK) hinge
- A decorative variety of barrel hinge with leaves somewhat resembling the wings of a butterfly.
- Case hinge
- Similar to butt hinges, but usually more decorative; most commonly used in suitcases, briefcases, and the like.
- Concealed hinge
- Used for furniture doors (with or without a self-closing features and/or damping systems), they consist of two parts
- Continuous / Piano hinge
- This variety of barrel hinge runs the entire length of a door, panel, box, etc. They are manufactured with or without holes.
- Flag hinge
- A simple two-part hinge, where a single leaf, attached to a pin, is inserted into a leaf with a hole. This allows the hinged objects to be easily removed (such as removable doors). They are made in right- and left-hand configurations.
- H hinge
- These H-shaped barrel hinges are used on flush-mounted doors. Small H hinges () tend to be used for cabinets, while larger ones () are for passage doors and closet doors.
- HL hinge
- Commonly used for passage doors, room doors, and closet doors in the 17th, 18th, and the 19th centuries. On taller doors, H hinges were occasionally used between them.
- Pivot hinge
- This hinge pivots in openings in the floor and the top of the door frame. Also referred to as double-acting floor hinges, they are found in ancient dry stone buildings and, rarely, in old wooden buildings. They are a low-cost alternative for use with lightweight doors.
- Self-closing hinge
- This is a spring-loaded hinge with a speed control function. The same as spring hinge, usually use spring to provide force to close the door and provide a mechanical or hydraulic damper to control door close speed. That can prevent door slamming problem while Door closer.
- Spring hinge
- A spring-loaded hinge that provides assistance in closing or opening the hinge leaves. An inner spring applies force to keep the hinge closed or opened.
- Swing Clear hinge
- Also called offset door hinges, they are ideal for residential and commercial doors, they allow doors to swing completely clear of their openings.
- Living hinge
- A hinge of flexible plastic that creates a join between two objects without any knuckles or pins. Molded as a single piece, they never rust or squeak, and have several other advantages over other hinges, but are more susceptible to breakage.
Other types of hinges include:
-
Coach
-
Counter Flap
-
Cranked or storm-proof
-
Double action non-spring
-
Double action spring
-
Flush
-
Friction
-
Lift-off
-
Pinge (with a quick-release pin)
-
Rising butt
-
Security
-
Tee
Building access
Since at least
medieval times, there have been hinges to
for defensive purposes for fortified buildings. Hinges are used in contemporary
architecture where building settlement can be expected over the life of the building. For example, the
Dakin Building in Brisbane,
California, was designed with its entrance ramp on a large hinge to allow settlement of the building built on piles over
bay mud. This device was effective until October 2006, when it was replaced due to damage and excessive ramp slope.
Large structures
Hinges appear in large structures such as elevated freeway and railroad viaducts, to reduce or eliminate the transfer of bending stresses between structural components, typically in an effort to reduce sensitivity to
earthquakes. The primary reason for using a hinge, rather than a simpler device such as a slide, is to prevent the separation of adjacent components. When no bending stresses are transmitted across the hinge, it is called a
zero moment hinge.
Spacecraft
A variety of self-actuating, self-locking hinges have been developed for spacecraft deployable structures such as
solar array panels, synthetic aperture radar antennas, booms, radiators, etc.
[
Alan M. Watt; and Sergio Pellegrino.
"Tape-Spring Rolling Hinges"
p. 2.
]
Terminology
Components
- Pin
- The rod that holds the leaves together, inside the knuckle. Also known as a pintle.
- Knuckle
- The hollow—typically circular—portion creating the joint of the hinge through which the pin is set. The knuckles of either leaf typically alternate and interlock with the pin passing through all of them. (aka. loop, joint, node or curl)
- Leaf
- The portions (typically two) that extend laterally from the knuckle and typically revolve around the pin.
Characteristics
- End play
- Axial movement between the leaves along the axis of the pin. This motion allows the leaves to rotate without binding and is determined by the typical distance between knuckles (knuckle gap) when both edges of the leaves are aligned.
- Gauge
- Thickness of the leaves.
- Hinge width
- Length from the outer edge of one leaf to the outer edge of the other leaf, perpendicularly across the pin (aka open width).
- Hinge length
- The length of the leaves parallel to the pin.
- Knuckle length
- The typical length of an individual knuckle parallel to the pin.
- Leaf width
- Length from the center of the pin to the outer edge of the leaf.
- Pitch
- Distance from the end of a knuckle to the same edge of its adjacent knuckle on the same leaf
- Doorstop
- A colloquialism referring to loose angular movement of the leaves relative to the pin.
Other types
- tray hinge
- Folds to 90 degrees and also snaps flat. They are for tables that have a tray top for serving.
- Card table hinge
- Mortised into edge of antique or reproduction card tables and allow the top to fold onto itself.
- Carpentier joint
- A hinge consisting of several thin metal strips of curved cross section.
- Drop-leaf table hinge
- Mounted under the surface of a table with leaves that drop down. They are most commonly used with rule joints.
- Hinged expansion joint
- an expansion joint with hinges that allow the unit to bend in a single plane
- Hinged handcuffs
- a restraint device designed to secure an individual's wrists in proximity to each other consisting of two cuffs linked with a double or triple hinge. Hinged handcuffs cuffs tend to restrict movement more than chain-linked handcuffs, and they can be used to generate more leverage to force a suspect's hands behind the back, or to apply pain against the wrist, forcing the subject to comply and stop resisting.
- Hinge region
- portion of antibody structure between the fragment antigen-binding region and the fragment crystallizable region
- Living hinge
- a hinge consisting of material that flexes
- Piano hinge
- (or coffin hinge) a long hinge, originally used for piano lids, but now used in many other applications where a long hinge is needed.
==Gallery==
See also
External links
