Bending

 ( Beam Theory ) 

In applied mechanics, bending (also known as flexure) characterizes the behavior of a slender structural element subjected to an external Structural load applied perpendicularly to a longitudinal axis of the element.

The structural element is assumed to be such that at least one of its dimensions is a small fraction, typically 1/10 or less, of the other two.Boresi, A. P. and Schmidt, R. J. and Sidebottom, O. M., 1993, Advanced mechanics of materials, John Wiley and Sons, New York. When the length is considerably longer than the width and the thickness, the element is called a beam. For example, a closet rod sagging under the weight of clothes on is an example of a beam experiencing bending. On the other hand, a shell is a structure of any geometric form where the length and the width are of the same order of magnitude but the thickness of the structure (known as the 'wall') is considerably smaller. A large diameter, but thin-walled, short tube supported at its ends and loaded laterally is an example of a shell experiencing bending.

In the absence of a qualifier, the term bending is ambiguous because bending can occur locally in all objects. Therefore, to make the usage of the term more precise, engineers refer to a specific object such as; the bending of rods, the bending of beams, the bending of plates,Timoshenko, S. and Woinowsky-Krieger, S., 1959, Theory of plates and shells, McGraw-Hill. the Plate theoryLibai, A. and Simmonds, J. G., 1998, The nonlinear theory of elastic shells, Cambridge University Press. and so on.

---

Quasi-static bending of beams A beam deforms and stresses develop inside it when a transverse load is applied on it. In the quasi-static case, the amount of bending deflection and the stresses that develop are assumed not to change over time. In a horizontal beam supported at the ends and loaded downwards in the middle, the material at the over-side of the beam is compressed while the material at the underside is stretched. There are two forms of internal stresses caused by lateral loads:

• Shear stress parallel to the lateral loading plus complementary shear stress on planes perpendicular to the load direction;
• Direct compressive stress in the upper region of the beam, applicable mostly to cement concreted elements and,
• Direct tensile stress, applicable to steel elements, and is at the lower region of the beam.

These last two forces form a couple or moment as they are equal in magnitude and opposite in direction. This bending moment resists the sagging deformation characteristic of a beam experiencing bending. The stress distribution in a beam can be predicted quite accurately when some simplifying assumptions are used.

---

Euler–Bernoulli bending theory In the Euler–Bernoulli theory of slender beams, a major assumption is that 'plane sections remain plane'. In other words, any deformation due to shear across the section is not accounted for (no shear deformation). Also, this linear distribution is only applicable if the maximum stress is less than the yield stress of the material. For stresses that exceed yield, refer to article plastic bending. At yield, the maximum stress experienced in the section (at the furthest points from the neutral axis of the beam) is defined as the flexural strength.

Consider beams where the following are true:

• The beam is originally straight and slender, and any taper is slight
• The material is isotropic (or orthotropic), linear elastic, and homogeneous across any cross section (but not necessarily along its length)
• Only small deflections are considered

In this case, the equation describing beam deflection ($w$) can be approximated as:

$\backslash cfrac\{\backslash mathrm\{d\}^2\; w(x)\}\{\backslash mathrm\{d\}\; x^2\}=\backslash frac\{M(x)\}\{E(x)\; I(x)\}$

where the second derivative of its deflected shape with respect to $x$ is interpreted as its curvature, $E$ is the Young's modulus, $I$ is the area moment of inertia of the cross-section, and $M$ is the internal bending moment in the beam.

If, in addition, the beam is homogeneous along its length as well, and not tapered (i.e. constant cross section), and deflects under an applied transverse load $q(x)$, it can be shown that:

$$

EI~\cfrac{\mathrm{d}^4 w(x)}{\mathrm{d} x^4} = q(x) This is the Euler–Bernoulli equation for beam bending.

After a solution for the displacement of the beam has been obtained, the bending moment ($M$) and shear force ($Q$) in the beam can be calculated using the relations

$$

M(x) = -EI~\cfrac{\mathrm{d}^2 w}{\mathrm{d} x^2} ~;~~ Q(x) = \cfrac{\mathrm{d}M}{\mathrm{d}x}.

Simple beam bending is often analyzed with the Euler–Bernoulli beam equation. The conditions for using simple bending theory are:Shigley J, "Mechanical Engineering Design", p44, International Edition, pub McGraw Hill, 1986,

1. The beam is subject to pure bending. This means that the shear force is zero, and that no torsional or axial loads are present.
2. The material is isotropic (or orthotropic) and homogeneous.
3. The material obeys Hooke's law (it is linearly elastic and will not deform plastically).
4. The beam is initially straight with a cross section that is constant throughout the beam length.
5. The beam has an axis of symmetry in the plane of bending.
6. The proportions of the beam are such that it would fail by bending rather than by crushing, wrinkling or sideways buckling.
7. Cross-sections of the beam remain plane during bending.

Compressive and tensile forces develop in the direction of the beam axis under bending loads. These forces induce stresses on the beam. The maximum compressive stress is found at the uppermost edge of the beam while the maximum tensile stress is located at the lower edge of the beam. Since the stresses between these two opposing vary , there therefore exists a point on the linear path between them where there is no bending stress. The locus of these points is the neutral axis. Because of this area with no stress and the adjacent areas with low stress, using uniform cross section beams in bending is not a particularly efficient means of supporting a load as it does not use the full capacity of the beam until it is on the brink of collapse. Wide-flange beams (i-Beam) and truss effectively address this inefficiency as they minimize the amount of material in this under-stressed region.

The classic formula for determining the bending stress in a beam under simple bending is:Gere, J. M. and Timoshenko, S.P., 1997, Mechanics of Materials, PWS Publishing Company.

$\backslash sigma\_x\; =\; \backslash frac\{M\_z\; y\}\{I\_z\}\; =\; \backslash frac\{M\_z\}\{W\_z\}$

where

• $\{\backslash sigma\_x\}$ is the bending stress
• $M\_z$ – the moment about the neutral axis
• $y$ – the perpendicular distance to the neutral axis
• $I\_z$ – the second moment of area about the neutral axis z.
• $W\_z$ - the Resistance Moment about the neutral axis z. $W\_z\; =\; I\_z\; /\; y$

---

Extensions of Euler-Bernoulli beam bending theory

---

Plastic bending The equation $\backslash sigma\; =\; \backslash tfrac\{M\; y\}\{I\_x\}$ is valid only when the stress at the extreme fiber (i.e., the portion of the beam farthest from the neutral axis) is below the yield stress of the material from which it is constructed. At higher loadings the stress distribution becomes non-linear, and ductile materials will eventually enter a plastic hinge state where the magnitude of the stress is equal to the yield stress everywhere in the beam, with a discontinuity at the neutral axis where the stress changes from tensile to compressive. This plastic hinge state is typically used as a limit state in the design of steel structures.

---

Complex or asymmetrical bending The equation above is only valid if the cross-section is symmetrical. For homogeneous beams with asymmetrical sections, the maximum bending stress in the beam is given by

$\backslash sigma\_x(y,z)\; =\; -\; \backslash frac\; \{M\_z~I\_y\; +\; M\_y~I\_\{yz\}\}\; \{I\_y~I\_z\; -\; I\_\{yz\}^2\}y\; +\; \backslash frac\; \{M\_y~I\_z\; +\; M\_z~I\_\{yz\}\}\; \{I\_y~I\_z\; -\; I\_\{yz\}^2\}z$Cook and Young, 1995, Advanced Mechanics of Materials, Macmillan Publishing Company: New York

where $y,z$ are the coordinates of a point on the cross section at which the stress is to be determined as shown to the right, $M\_y$ and $M\_z$ are the bending moments about the y and z centroid axes, $I\_y$ and $I\_z$ are the second moments of area (distinct from moments of inertia) about the y and z axes, and $I\_\{yz\}$ is the product of moments of area. Using this equation it is possible to calculate the bending stress at any point on the beam cross section regardless of moment orientation or cross-sectional shape. Note that $M\_y,\; M\_z,\; I\_y,\; I\_z,\; I\_\{yz\}$ do not change from one point to another on the cross section.

---

Large bending deformation For large deformations of the body, the stress in the cross-section is calculated using an extended version of this formula. First the following assumptions must be made:

1. Assumption of flat sections – before and after deformation the considered section of body remains flat (i.e., is not swirled).
2. Shear and normal stresses in this section that are perpendicular to the normal vector of cross section have no influence on normal stresses that are parallel to this section.

Large bending considerations should be implemented when the bending radius $\backslash rho$ is smaller than ten section heights h:

With those assumptions the stress in large bending is calculated as:

$$

where

$F$ is the normal force

$A$ is the section area

$M$ is the bending moment

$\backslash rho$ is the local bending radius (the radius of bending at the current section)

$\{\backslash mathrm\{d\}x^4\}\; -\; m\backslash omega^2\backslash hat\{w\}\; =\; 0$

The general solution of the above equation is

$$

  \hat{w} = A_1\cosh(\beta x) + A_2\sinh(\beta x) + A_3\cos(\beta x) + A_4\sin(\beta x)
     
     

where $A\_1,A\_2,A\_3,A\_4$ are constants and $$

 \beta := \left(\cfrac{m}{EI}~\omega^2\right)^{1/4}
     

---

Timoshenko–Rayleigh theory In 1877, Rayleigh proposed an improvement to the dynamic Euler–Bernoulli beam theory by including the effect of rotational inertia of the cross-section of the beam. Timoshenko improved upon that theory in 1922 by adding the effect of shear into the beam equation. Shear deformations of the normal to the mid-surface of the beam are allowed in the Timoshenko–Rayleigh theory.

The equation for the bending of a linear elastic, isotropic, homogeneous beam of constant cross-section under these assumptions isRosinger, H. E. and Ritchie, I. G., 1977, On Timoshenko's correction for shear in vibrating isotropic beams, J. Phys. D: Appl. Phys., vol. 10, pp. 1461–1466.

$$

\begin{align} & EI~\frac{\partial^4 w}{\partial x^4} + m~\frac{\partial^2 w}{\partial t^2} - \left(J + \frac{E I m}{k A G}\right)\frac{\partial^4 w}{\partial x^2~\partial t^2} + \frac{J m}{k A G}~\frac{\partial^4 w}{\partial t^4} \\6pt = {} & q(x,t) + \frac{J}{k A G}~\frac{\partial^2 q}{\partial t^2} - \frac{EI}{k A G}~\frac{\partial^2 q}{\partial x^2} \end{align}

where $J\; =\; \backslash tfrac\{mI\}\{A\}$ is the polar moment of inertia of the cross-section, $m\; =\; \backslash rho\; A$ is the mass per unit length of the beam, $\backslash rho$ is the density of the beam, $A$ is the cross-sectional area, $G$ is the shear modulus, and $k$ is a shear correction factor. For materials with Poisson's ratios ($\backslash nu$) close to 0.3, the shear correction factor are approximately

$$

   \begin{align}
   k &= \frac{5 + 5\nu}{6 + 5\nu} \quad \text{rectangular cross-section}\\[6pt]
     &= \frac{6 + 12\nu + 6\nu^2}{7 + 12\nu + 4\nu^2} \quad \text{circular cross-section}
   \end{align}
     
     

---

Free vibrations For free, harmonic vibrations the Timoshenko–Rayleigh equations take the form

$$

  EI~\cfrac{\mathrm{d}^4 \hat{w}}{\mathrm{d} x^4} + m\omega^2\left(\cfrac{J}{m} + \cfrac{E I}{k A G}\right)\cfrac{\mathrm{d}^2 \hat{w}}{\mathrm{d} x^2} + m\omega^2\left(\cfrac{\omega^2 J}{k A G}-1\right)~\hat{w} = 0
     
     

This equation can be solved by noting that all the derivatives of $w$ must have the same form to cancel out and hence as solution of the form $e^\{kx\}$ may be expected. This observation leads to the characteristic equation

$$

  \alpha~k^4 + \beta~k^2 + \gamma = 0 ~;~~ \alpha := EI ~,~~ \beta := m\omega^2\left(\cfrac{J}{m} + \cfrac{E I}{k A G}\right) ~,~~ \gamma := m\omega^2\left(\cfrac{\omega^2 J}{k A G}-1\right)
     
     

The solutions of this quartic equation are

$$

  k_1 = +\sqrt{z_+} ~,~~ k_2 = -\sqrt{z_+} ~,~~ k_3 = +\sqrt{z_-} ~,~~ k_4 = -\sqrt{z_-}
     
     

where

$$

  z_+ := \cfrac{-\beta + \sqrt{\beta^2 - 4\alpha\gamma}}{2\alpha} ~,~~
  z_-:= \cfrac{-\beta - \sqrt{\beta^2 - 4\alpha\gamma}}{2\alpha}
     
     

The general solution of the Timoshenko-Rayleigh beam equation for free vibrations can then be written as

$$

  \hat{w} = A_1~e^{k_1 x} + A_2~e^{-k_1 x} + A_3~e^{k_3 x} + A_4~e^{-k_3 x}
     
     

---

Quasistatic bending of plates The defining feature of beams is that one of the dimensions is much larger than the other two. A structure is called a plate when it is flat and one of its dimensions is much smaller than the other two. There are several theories that attempt to describe the deformation and stress in a plate under applied loads two of which have been used widely. These are

• the Kirchhoff–Love theory of plates (also called classical plate theory)
• the Mindlin–Reissner plate theory (also called the first-order shear theory of plates)

---

Kirchhoff–Love theory of plates The assumptions of Kirchhoff–Love theory are

• straight lines normal to the mid-surface remain straight after deformation
• straight lines normal to the mid-surface remain normal to the mid-surface after deformation
• the thickness of the plate does not change during a deformation.

These assumptions imply that

$$

  \begin{align}
    u_\alpha(\mathbf{x}) & = - x_3~\frac{\partial w^0}{\partial x_\alpha}
        = - x_3~w^0_{,\alpha} ~;~~\alpha=1,2 \\
    u_3(\mathbf{x}) & = w^0(x_1, x_2)
  \end{align}
     

where $\backslash mathbf\{u\}$ is the displacement of a point in the plate and $w^0$ is the displacement of the mid-surface.

The strain-displacement relations are

$$

 \begin{align}
   \varepsilon_{\alpha\beta} & =
     - x_3~w^0_{,\alpha\beta} \\
   \varepsilon_{\alpha 3} & = 0 \\
   \varepsilon_{33} & = 0
 \end{align}
     

The equilibrium equations are

$$

    M_{\alpha\beta,\alpha\beta} + q(x) = 0 ~;~~ M_{\alpha\beta} := \int_{-h}^h x_3~\sigma_{\alpha\beta}~dx_3
     

where $q(x)$ is an applied load normal to the surface of the plate.

In terms of displacements, the equilibrium equations for an isotropic, linear elastic plate in the absence of external load can be written as

$$

  w^0_{,1111} + 2~w^0_{,1212} + w^0_{,2222} = 0
     
     

In direct tensor notation,

$$

  \nabla^2\nabla^2 w = 0
     
     

---

Mindlin–Reissner theory of plates The special assumption of this theory is that normals to the mid-surface remain straight and inextensible but not necessarily normal to the mid-surface after deformation. The displacements of the plate are given by

$$

  \begin{align}
    u_\alpha(\mathbf{x}) & = - x_3~\varphi_\alpha ~;~~\alpha=1,2 \\
    u_3(\mathbf{x}) & = w^0(x_1, x_2)
  \end{align}
     

where $\backslash varphi\_\backslash alpha$ are the rotations of the normal.

The strain-displacement relations that result from these assumptions are

$$

 \begin{align}
   \varepsilon_{\alpha\beta} & =
     - x_3~\varphi_{\alpha,\beta} \\
   \varepsilon_{\alpha 3} & = \cfrac{1}{2}~\kappa\left(w^0_{,\alpha}- \varphi_\alpha\right) \\
   \varepsilon_{33} & = 0
 \end{align}
     

where $\backslash kappa$ is a shear correction factor.

The equilibrium equations are

$$

  \begin{align}
    & M_{\alpha\beta,\beta}-Q_\alpha = 0 \\
    & Q_{\alpha,\alpha}+q = 0
  \end{align}
     
     

where

$$

  Q_\alpha := \kappa~\int_{-h}^h \sigma_{\alpha 3}~dx_3
     

---

Dynamic bending of plates

---

Dynamics of thin Kirchhoff plates The dynamic theory of plates determines the propagation of waves in the plates, and the study of standing waves and vibration modes. The equations that govern the dynamic bending of Kirchhoff plates are

$$

    M_{\alpha\beta,\alpha\beta} - q(x,t) = J_1~\ddot{w}^0 - J_3~\ddot{w}^0_{,\alpha\alpha}
     

where, for a plate with density $\backslash rho\; =\; \backslash rho(x)$,

$$

  J_1 := \int_{-h}^h \rho~dx_3  ~;~~
  J_3 := \int_{-h}^h x_3^2~\rho~dx_3
     

and

$$

  \ddot{w}^0 = \frac{\partial^2 w^0}{\partial t^2} ~;~~
  \ddot{w}^0_{,\alpha\beta} = \frac{\partial^2 \ddot{w}^0}{\partial x_\alpha\, \partial x_\beta}
     

The figures below show some vibrational modes of a circular plate. File:Drum vibration mode01.gif|mode k = 0, p = 1 File:Drum vibration mode02.gif|mode k = 0, p = 2 File:Drum vibration mode12.gif|mode k = 1, p = 2

---

See also

• Bending moment
• Bending Machine (flat metal bending)
• Brake (sheet metal bending)
• Brazier effect
• Bending of plates
• Bending (metalworking)
• Continuum mechanics
• Contraflexure
• Deflection (engineering)
• Flexure bearing
• List of area moments of inertia
• Pipe bending

• Shear and moment diagram
• Shear strength
• Sandwich theory
• Vibration
• Vibration of plates

---

External links

• Flexure formulae
• Beam stress & deflection, beam deflection tables
• What is Bending Stress?

Post Comment