Product Code Database
Fluorocarbons are chemical compounds with carbon-fluorine bonds. Compounds that contain many C-F bonds often have distinctive properties, e.g., enhanced stability, volatility, and hydrophobicity. Several fluorocarbons and their derivatives are commercial fluoropolymer, refrigerants, , and .
Fluorocarbons includes perfluoroalkanes, fluoroalkenes, fluoroalkynes, and perfluoroaromatic compounds.
Its strength is a result of the electronegativity of fluorine imparting partial ionic character through on the carbon and fluorine atoms, which shorten and strengthen the bond (compared to carbon-hydrogen bonds) through favorable covalent interactions. Additionally, multiple carbon–fluorine bonds increase the strength and stability of other nearby carbon–fluorine bonds on the same geminal carbon, as the carbon has a higher positive partial charge. Furthermore, multiple carbon–fluorine bonds also strengthen the "skeletal" carbon–carbon bonds from the inductive effect. Therefore, saturated fluorocarbons are more chemically and thermally stable than their corresponding hydrocarbon counterparts, and indeed any other organic compound. They are susceptible to attack by very strong reductants, e.g. Birch reduction and very specialized organometallic complexes.
Fluorocarbons are colorless and have high density, up to over twice that of water. They are not miscible with most organic solvents (e.g., ethanol, acetone, ethyl acetate, and chloroform), but are miscible with some hydrocarbons (e.g., hexane in some cases). They have very low solubility in water, and water has a very low solubility in them (on the order of 10 ppm). They have low refractive index.
As the high electronegativity of fluorine reduces the polarizability of the atom, fluorocarbons are only weakly susceptible to the fleeting dipoles that form the basis of the London dispersion force. As a result, fluorocarbons have low intermolecular attractive forces and are lipophobic in addition to being hydrophobe and non-polar. Reflecting the weak intermolecular forces these compounds exhibit low viscosity when compared to liquids of similar , low surface tension and low heats of vaporization. The low in fluorocarbon liquids make them compressible (low bulk modulus) and able to dissolve gas relatively well. Smaller fluorocarbons are extremely volatile. There are five perfluoroalkane gases: tetrafluoromethane (bp −128 °C), hexafluoroethane (bp −78.2 °C), octafluoropropane (bp −36.5 °C), perfluorobutane (bp −2.2 °C) and perfluoro-iso-butane (bp −1 °C). Nearly all other fluoroalkanes are liquids; the most notable exception is perfluorocyclohexane, which sublimes at 51 °C. Fluorocarbons also have low surface energy and high dielectric strengths.
In 1993, 3M considered fluorocarbons as fire extinguishants to replace CFCs. This extinguishing effect has been attributed to their high heat capacity, which takes heat away from the fire. It has been suggested that an atmosphere containing a significant percentage of perfluorocarbons on a space station or similar would prevent fires altogether.
When combustion does occur, toxic fumes result, including carbonyl fluoride, carbon monoxide, and hydrogen fluoride.
The table shows values for the mole fraction, , of nitrogen dissolved, calculated from the Blood–gas partition coefficient, at 298.15 K (25 °C), 0.101325 MPa.
The resulting cobalt difluoride is then regenerated, sometimes in a separate reactor:
Industrially, both steps are combined, for example in the manufacture of the Flutec range of fluorocarbons by F2 chemicals Ltd, using a vertical stirred bed reactor, with hydrocarbon introduced at the bottom, and fluorine introduced halfway up the reactor. The fluorocarbon vapor is recovered from the top.
The perfluorinated amine will also be produced:
Fluoroalkanes are not ozone depletion, as they contain no chlorine or bromine atoms, and they are sometimes used as replacements for ozone-depleting chemicals.
The term fluorocarbon is used rather loosely to include any chemical containing fluorine and carbon, including chlorofluorocarbons, which are ozone depleting.
Perfluoroalkanes used in medical procedures are rapidly excreted from the body, primarily via expiration with the rate of excretion as a function of the vapour pressure; the half-life for octafluoropropane is less than 2 minutes, compared to about a week for perfluorodecalin.
Low-boiling perfluoroalkanes are potent greenhouse gases, in part due to their very long atmospheric lifetime, and their use is covered by the Kyoto Protocol. The global warming potential (compared to that of carbon dioxide) of many gases can be found in the IPCC 5th assessment report,Myhre, G., D. Shindell, F.-M. Bréon, W. Collins, J. Fuglestvedt, J. Huang, D. Koch, J.-F. Lamarque, D. Lee, B. Mendoza, T. Nakajima, A. Robock, G. Stephens, T. Takemura and H. Zhang (2013) "Anthropogenic and Natural Radiative Forcing" (see Table 8.A.1). In: Climate Change 2013: The Physical Science Basis. Contribution of Working Group I to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change. Stocker, T.F., D. Qin, G.-K. Plattner, M. Tignor, S.K. Allen, J. Boschung, A. Nauels, Y. Xia, V. Bex and P.M. Midgley (eds.). Cambridge University Press, Cambridge, United Kingdom and New York, NY, USA. with an extract below for a few perfluoroalkanes.
The aluminium smelting industry has been a major source of atmospheric perfluorocarbons (tetrafluoromethane and hexafluoroethane especially), produced as by-product of the electrolysis process. However, the industry has been actively involved in reducing emissions in recent years. climatevision.gov
Perfluoroaromatic compounds can be manufactured via the Fowler process, like fluoroalkanes, but the conditions must be adjusted to prevent full fluorination. They can also be made by heating the corresponding perchloroaromatic compound with potassium fluoride at high temperature (typically 500 °C), during which the chlorine atoms are replaced by fluorine atoms. A third route is defluorination of the fluoroalkane; for example, octafluorotoluene can be made from perfluoromethylcyclohexane by heating to 500 °C with a nickel or iron catalyst.
Perfluoroaromatic compounds are relatively volatile for their molecular weight, with melting and boiling points similar to the corresponding aromatic compound, as the table below shows. They have high density and are non-flammable. For the most part, they are colorless liquids. Unlike the perfluoralkanes, they tend to be miscible with common solvents.
Flammability
In the 1960s there was a lot of interest in fluorocarbons as anesthetics. The research did not produce any anesthetics, but the research included tests on the issue of flammability, and showed that the tested fluorocarbons were not flammable in air in any proportion, though most of the tests were in pure oxygen or pure nitrous oxide (gases of importance in anesthesiology).
Hexafluoroethane Lower flammability limit in oxygen None Perfluoropentane Flash point in air None Flash point in oxygen −6 °C Flash point nitrous oxide −32 °C Perfluoromethylcyclohexane Lower flammability limit in air None Lower flammability limit in oxygen 8.3% Lower flammability limit in oxygen (50 °C) 7.4% Lower flammability limit in nitrous oxide 7.7% Perfluoro-1,3-dimethylcyclohexane Lower flammability limit in oxygen (50 °C) 5.2% Perfluoromethyldecalin Spontaneous ignition test
in oxygen at 127 barNo ignition at 500 °C Spontaneous ignition in adiabatic shock
wave in oxygen, 0.98 to 186 barNo ignition Spontaneous ignition in adiabatic shock
wave in oxygen, 0.98 to 196 barIgnition
Gas dissolving properties
Perfluorocarbons dissolve relatively high volumes of gases. The high solubility of gases is attributed to the weak intermolecular interactions in these fluorocarbon fluids.
Water 0.118 0.65 Ethanol 3.57 6.12 Tetrahydrofuran 5.21 6.42 Acetone 5.42 7.32 Cyclohexane 7.73 7.16 Perfluoro-1,3-dimethylcyclohexane 31.9 14.6 Perfluoromethylcyclohexane 33.1 16.9
Manufacture
The development of the fluorocarbon industry coincided with World War II. Prior to that, fluorocarbons were prepared by reaction of fluorine with the hydrocarbon, i.e., direct fluorination. Because C-C bonds are readily cleaved by fluorine, direct fluorination mainly affords smaller perfluorocarbons, such as tetrafluoromethane, hexafluoroethane, and octafluoropropane.
Fowler process
A major breakthrough that allowed the large scale manufacture of fluorocarbons was the Fowler process. In this process, cobalt trifluoride is used as the source of fluorine. Illustrative is the synthesis of perfluorohexane:
Electrochemical fluorination
Electrochemical fluorination (ECF) (also known as the Simons' process) involves electrolysis of a substrate dissolved in hydrogen fluoride. As fluorine is itself manufactured by the electrolysis of hydrogen fluoride, ECF is a rather more direct route to fluorocarbons. The process proceeds at low voltage (5 – 6 V) so that free fluorine is not liberated. The choice of substrate is restricted as ideally it should be soluble in hydrogen fluoride. Ethers and tertiary amines are typically employed. To make perfluorohexane, trihexylamine is used, for example:
Environmental and health concerns
Fluoroalkanes are generally inert and non-toxic.
6630 11100 9200 8900 9540
Applications
As they are inert, perfluoroalkanes have essentially no chemical uses, but their physical properties have led to their use in many diverse applications. These include:
As well as several medical uses:
Fluoroalkenes and fluoroalkynes
Unsaturated fluorocarbons are far more reactive than fluoroalkanes. Although difluoroacetylene is unstable (as is typical for related alkynes, see dichloroacetylene), hexafluoro-2-butyne and related fluorinated alkynes are well known.
Polymerization
Fluoroalkenes polymerize more exothermically than normal alkenes. Unsaturated fluorocarbons have a driving force towards sp3 hybridization due to the electronegative fluorine atoms seeking a greater share of bonding electrons with reduced s character in orbitals. The most famous member of this class is tetrafluoroethylene, which is used to manufacture polytetrafluoroethylene (PTFE), better known under the trade name Teflon.
Environmental and health concerns
Fluoroalkenes and fluorinated alkynes are reactive and many are toxic for example perfluoroisobutene. (2025). 9780080434056 ISBN 9780080434056 To produce polytetrafluoroethylene various fluorinated surfactants are used, in the process known as Emulsion polymerization, and the surfactant included in the polymer can bioaccumulate.
Perfluoroaromatic compounds
Perfluoroaromatic compounds contain only carbon and fluorine, like other fluorocarbons, but also contain an aromatic ring. The three most important examples are hexafluorobenzene, Perfluorotoluene, and octafluoronaphthalene.
Hexafluorobenzene 5.3 80.5 Benzene 5.5 80.1 Octafluorotoluene <−70 102–103 Toluene −95 110.6 Perfluoro(ethylbenzene) 114–115 Ethylbenzene −93.9 136.2 Octafluoronaphthalene 86–87 209 Naphthalene 80.2 217.9
See also
External links
|
|
