Morse code is a method used in telecommunication to encode written language characters as standardized sequences of two different signal durations, called dots and dashes or dits and dahs.F. S. Beechey, Electro-Telegraphy, London: E. & F. N. Spon, 1876, p. 71F. J. Camm, Radio Engineer's Pocket Book, 2nd ed., Chemical Publishing Co., 1941, p. 72 Morse code is named for Samuel F. B. Morse, an inventor of the telegraph.
The International Morse Code encodes the 26 English letters A through Z, some non-English letters, the Arabic numerals and a small set of punctuation and procedural signals (prosigns). There is no distinction between upper and lower case letters. Each Morse code symbol is formed by a sequence of dots and dashes. The dot duration is the basic unit of time measurement in Morse code transmission. The duration of a dash is three times the duration of a dot. Each dot or dash within a character is followed by period of signal absence, called a space, equal to the dot duration. The letters of a word are Delimiter a space of duration equal to three dots, and the words are separated by a space equal to seven dots. To increase the efficiency of encoding, Morse code was designed so that the length of each symbol is approximately entropy encoding in text of the English language character that it represents. Thus the most common letter in English, the letter "E", has the shortest code: a single dot. Because the Morse code elements are specified by proportion rather than specific time durations, the code is usually transmitted at the highest rate that the receiver is capable of decoding. The Morse code transmission rate ( speed) is specified in groups per minute, commonly referred to as words per minute.Headquarters, Department of the Army, TM 11-459, International Morse Code (Instructions), Washington, D.C.: U.S.G.P.O., 1968 pp. 7-8
Morse code is usually transmitted by on-off keying of an information-carrying medium such as electric current, radio waves, visible light, or sound waves.W.H. Preece, J. Sivewright, Telegraphy, London: Longmans, Green and Co., 1891, p. 40U.S. Army, FM 24-5, Signal Communication, 1939, pp. 83, 101-108, 227 The current or wave is present during the time period of the dot or dash and absent during the time between dots and dashes.W. L. Everitt, Communication Engineering, 2nd ed. New York: McGraw-Hill, 1937, p. 6Editors and Engineers, The "Radio" Handbook, Los Angeles: Editors and Engineers, 1942, p. 180
Morse code can be memorized, and Morse code signalling in a form perceptible to the human senses, such as sound waves or visible light, can be directly interpreted by persons trained in the skill.Headquarters, Department of the Army, TM 11-459, International Morse Code (Instructions), Washington, D.C.: U.S.G.P.O., 1968, pp. 6-7U. S. Navy, Bureau of Naval Personnel, Radioman 3 & 2, Washington, D.C.: U.S.G.P.O., 1957, pp. 105-111
Because many non-English natural languages use other than the 26 Roman letters, Morse alphabets have been developed for those languages.War Department, TM 11-459, Instructions for Learning International Morse Characters, 1943, pp. 52, 68-72
In an emergency, Morse code can be generated by improvised methods such as turning a light on and off, tapping on an object or sounding a horn or whistle, making it one of the simplest and most versatile methods of telecommunication. The most common distress signal is SOS – three dots, three dashes, and three dots – internationally recognized by treaty.
Following the discovery of electromagnetism by Hans Christian Ørsted in 1820 and the invention of the electromagnet by William Sturgeon in 1824, there were developments in electromagnetic telegraphy in Europe and America. Pulses of electric current were sent along wires to control an electromagnet in the receiving instrument. Many of the earliest telegraph systems used a single-needle system which gave a very simple and robust instrument. However, it was slow, as the receiving operator had to alternate between looking at the needle and writing down the message. In Morse code, a deflection of the needle to the left corresponded to a dot and a deflection to the right to a dash. By making the two clicks sound different with one ivory and one metal stop, the single needle device became an audible instrument, which led in turn to the Double Plate Sounder System.
The American artist Samuel F. B. Morse, the American physicist Joseph Henry, and Alfred Vail developed an electrical telegraph system. It needed a method to transmit natural language using only electrical pulses and the silence between them. Around 1837, Morse, therefore, developed an early forerunner to the modern International Morse code. William Cooke and Charles Wheatstone in United Kingdom developed an electrical telegraph that used electromagnets in its receivers. They obtained an English patent in June 1837 and demonstrated it on the London and Birmingham Railway, making it the first commercial telegraph. Carl Friedrich Gauss and Wilhelm Eduard Weber (1833) as well as Carl August von Steinheil (1837) used codes with varying word lengths for their telegraphs. In 1841, Cooke and Wheatstone built a telegraph that printed the letters from a wheel of typefaces struck by a hammer.
The Morse system for telegraphy, which was first used in about 1844, was designed to make indentations on a paper tape when electric currents were received. Morse's original telegraph receiver used a mechanical clockwork to move a paper tape. When an electrical current was received, an electromagnet engaged an armature that pushed a stylus onto the moving paper tape, making an indentation on the tape. When the current was interrupted, a spring retracted the stylus and that portion of the moving tape remained unmarked. Morse code was developed so that operators could translate the indentations marked on the paper tape into text messages. In his earliest code, Morse had planned to transmit only numerals and to use a codebook to look up each word according to the number which had been sent. However, the code was soon expanded by Alfred Vail in 1840 to include letters and special characters so it could be used more generally. Vail estimated the frequency of use of letters in the English language by counting the movable type he found in the type-cases of a local newspaper in Morristown. The shorter marks were called "dots" and the longer ones "dashes", and the letters most commonly used were assigned the shorter sequences of dots and dashes. This code was used since 1844 and became known as Morse landline code or American Morse code. In the original Morse telegraphs, the receiver's armature made a clicking noise as it moved in and out of position to mark the paper tape. The telegraph operators soon learned that they could translate the clicks directly into dots and dashes, and write these down by hand, thus making the paper tape unnecessary. When Morse code was adapted to radio communication, the dots and dashes were sent as short and long tone pulses. It was later found that people become more proficient at receiving Morse code when it is taught as a language that is heard, instead of one read from a page.
To reflect the sounds of Morse code receivers, the operators began to vocalize a dot as "dit", and a dash as "dah". Dots which are not the final element of a character became vocalized as "di". For example, the letter "c" was then vocalized as "dah-di-dah-dit".L. Peter Carron, "Morse Code: The Essential Language", Radio amateur's library, issue 69, American Radio Relay League, 1986 .R. J. Eckersley, Amateur radio operating manual, Radio Society of Great Britain, 1985 . Morse code was sometimes facetiously known as "iddy-umpty" and a dash as "umpty", leading to the word "umpteen". (available online to subscribers)
The Morse code, as it is used internationally today, was derived from a much refined proposal by Friedrich Clemens Gerke in 1848 that became known as the "Hamburg alphabet". Gerke changed many of the codepoints, in the process doing away with the different length dashes and different inter-element spaces of American Morse, leaving only two coding elements, the dot and the dash. Codes for German umlauted vowels and "ch" were introduced. Gerke's code was adopted by the Deutsch-Österreichischer Telegraphenverein (German-Austrian Telegraph Society) in 1851. This finally led to the International Morse code in 1865. The International Morse code adopted most of Gerke's codepoints. The codepoints for "O" and "P" were taken from Steinheil's code. A new codepoint was added for "J" since Gerke did not distinguish between "I" and "J". Changes were also made to "Q", "X", "Y", "Z". This left only four codepoints identical to the original Morse code, namely "E", "H", "K" and "N", and the latter two have had their dashes lengthened. The original code being compared dates to 1838, not the code shown in the table which was developed in the 1840s. Annual Report of the Board of Regents of the Smithsonian Instution for 1878, pp. 358–360, Smithsonian Institution, 1879.
In the 1890s, Morse code began to be used extensively for early radio communication before it was possible to transmit voice. In the late 19th and early 20th centuries, most high-speed international communication used Morse code on telegraph lines, undersea cables and radio circuits. In aviation, Morse code in radio systems started to be used on a regular basis in the 1920s. Although previous transmitters were bulky and the spark gap system of transmission was difficult to use, there had been some earlier attempts. In 1910, the US Navy experimented with sending Morse from an airplane. That same year, a radio on the airship America had been instrumental in coordinating the rescue of its crew. Zeppelin airships equipped with radio were used for bombing and naval scouting during World War I, and ground-based radio direction finders were used for airship navigation. Allied airships and military aircraft also made some use of radiotelegraphy. However, there was little aeronautical radio in general use during World War I, and in the 1920s, there was no radio system used by such important flights as that of Charles Lindbergh from New York to Paris in 1927. Once he and the Spirit of St. Louis were off the ground, Lindbergh was truly alone and incommunicado. On the other hand, when the first airplane flight was made from California to Australia in 1928 on the Southern Cross, one of its four crewmen was its radio operator who communicated with ground stations via radio telegraph.
Beginning in the 1930s, both civilian and military pilots were required to be able to use Morse code, both for use with early communications systems and for identification of navigational beacons which transmitted continuous two- or three-letter identifiers in Morse code. Aeronautical charts show the identifier of each navigational aid next to its location on the map.
Radiotelegraphy using Morse code was vital during World War II, especially in carrying messages between the and the of the belligerents. Long-range ship-to-ship communication was by radio telegraphy, using encrypted messages because the voice radio systems on ships then were quite limited in both their range and their security. Radiotelegraphy was also extensively used by , especially by long-range scout plane that were sent out by those navies to scout for enemy warships, cargo ships, and troop ships.
In addition, rapidly moving armies in the field could not have fought effectively without radiotelegraphy because they moved more rapidly than telegraph and telephone lines could be erected. This was seen especially in the blitzkrieg offensives of the Nazi German Wehrmacht in Poland, Belgium, France (in 1940), the Soviet Union, and in North Africa; by the British Army in North Africa, Italy, and the Netherlands; and by the U.S. Army in France and Belgium (in 1944), and in southern Germany in 1945.
Morse code was used as an international standard for maritime distress until 1999 when it was replaced by the Global Maritime Distress and Safety System. When the French Navy ceased using Morse code on January 31, 1997, the final message transmitted was "Calling all. This is our last cry before our eternal silence." "An obituary for Morse code" , The Economist, January 23, 1999. In the United States the final commercial Morse code transmission was on July 12, 1999, signing off with Samuel Morse's original 1844 message, "", and the prosign "SK".
As of 2015, the United States Air Force still trains ten people a year in Morse. The United States Coast Guard has ceased all use of Morse code on the radio, and no longer monitors any radio frequencies for Morse code transmissions, including the international medium frequency (MF) distress frequency of 500 kHz. However, the Federal Communications Commission still grants commercial radiotelegraph operator licenses to applicants who pass its code and written tests. Licensees have reactivated the old California coastal Morse station KPH and regularly transmit from the site under either this call sign or as KSM. Similarly, a few U.S. museum ship stations are operated by Morse enthusiasts.
In addition to knowing, understanding, and being able to copy the standard written alpha-numeric and punctuation characters or symbols at high speeds, skilled high speed operators must also be fully knowledgeable of all of the special unwritten Morse code symbols for the standard Prosigns for Morse code and the meanings of these special procedural signals in standard Morse code communications protocol.
International contests in code copying are still occasionally held. In July 1939 at a contest in Asheville, North Carolina in the United States Ted R. McElroy W1JYN set a still-standing record for Morse copying, 75.2 wpm. William Pierpont N0HFF also notes that some operators may have passed 100 wpm. By this time, they are "hearing" phrases and sentences rather than words. The fastest speed ever sent by a straight key was achieved in 1942 by Harry Turner W9YZE (d. 1992) who reached 35 wpm in a demonstration at a U.S. Army base. To accurately compare code copying speed records of different eras it is useful to keep in mind that different standard words (50 dot durations versus 60 dot durations) and different interword gaps (5 dot durations versus 7 dot durations) may have been used when determining such speed records. For example, speeds run with the CODEX standard word and the PARIS standard may differ by up to 20%.
Today among amateur operators there are several organizations that recognize high-speed code ability, one group consisting of those who can copy Morse at 60 wpm. Also, Certificates of Code Proficiency are issued by several amateur radio societies, including the American Radio Relay League. Their basic award starts at 10 wpm with endorsements as high as 40 wpm, and are available to anyone who can copy the transmitted text. Members of the Boy Scouts of America may put a Morse interpreter's strip on their uniforms if they meet the standards for translating code at 5 wpm.
The original amateur radio operators used Morse code exclusively since voice-capable radio transmitters did not become commonly available until around 1920. Until 2003, the International Telecommunication Union mandated Morse code proficiency as part of the amateur radio licensing procedure worldwide. However, the World Radiocommunication Conference of 2003 made the Morse code requirement for amateur radio licensing optional. Many countries subsequently removed the Morse requirement from their licence requirements.
Until 1991, a demonstration of the ability to send and receive Morse code at a minimum of five words per minute (wpm) was required to receive an amateur radio license for use in the United States from the Federal Communications Commission. Demonstration of this ability was still required for the privilege to use the High frequency. Until 2000, proficiency at the 20 wpm level was required to receive the highest level of amateur license (Amateur Extra Class); effective April 15, 2000, the FCC reduced the Extra Class requirement to five wpm. Finally, effective on February 23, 2007, the FCC eliminated the Morse code proficiency requirements from all amateur radio licenses.
While voice and data transmissions are limited to specific amateur radio bands under U.S. rules, Morse code is permitted on all amateur bands—LF, MF, HF, VHF, and UHF. In some countries, certain portions of the amateur radio bands are reserved for transmission of Morse code signals only.
The relatively limited speed at which Morse code can be sent led to the development of an extensive number of abbreviations to speed communication. These include prosigns, , and a set of Morse code abbreviations for typical message components. For example, CQ is broadcast to be interpreted as "seek you" (I'd like to converse with anyone who can hear my signal). OM (old man), YL (young lady) and XYL ("ex-YL" – wife) are common abbreviations. YL or OM is used by an operator when referring to the other operator, XYL or OM is used by an operator when referring to his or her spouse. QTH is "location" ("My QTH" is "My location"). The use of abbreviations for common terms permits conversation even when the operators speak different languages.
Although the traditional telegraph key (straight key) is still used by some amateurs, the use of mechanical semi-automatic (known as "bugs") and of fully automatic electronic is prevalent today. Software is also frequently employed to produce and decode Morse code radio signals.
Many amateur radio repeaters identify with Morse, even though they are used for voice communications.
Radio navigation aids such as VORs and NDBs for aeronautical use broadcast identifying information in the form of Morse Code, though many VOR stations now also provide voice identification. Warships, including those of the U.S. Navy, have long used to exchange messages in Morse code. Modern use continues, in part, as a way to communicate while maintaining radio silence.
ATIS (Automatic Transmitter Identification System) uses Morse code to identify uplink sources of analog satellite transmissions.
Some Nokia mobile phones offer an option to alert the user of an incoming text message with the Morse tone "" (representing SMS or Short Message Service). In addition, applications are now available for mobile phones that enable short messages to be input in Morse Code. Nokia files patent for Morse Code-generating cellphone , 12 March 2005, Engadget.
Morse can be sent by persons with severe motion disabilities, as long as they have some minimal motor control. An original solution to the problem that caretakers have to learn to decode has been an electronic typewriter with the codes written on the keys. Codes were sung by users; see the voice typewriter employing morse or votem, Newell and Nabarro, 1968.
Morse code can also be translated by computer and used in a speaking communication aid. In some cases, this means alternately blowing into and sucking on a plastic tube ("sip-and-puff" interface). An important advantage of Morse code over row column scanning is that once learned, it does not require looking at a display. Also, it appears faster than scanning.
In one case reported in the radio amateur magazine QST,Dennis W. Ross, "Morse Code: A Place in the Mind," QST, March, 1992, p. 51. an old shipboard radio operator who had a stroke and lost the ability to speak or write could communicate with his physician (a radio amateur) by blinking his eyes in Morse. Two examples of communication in intensive care units were also published in QST,Ronald J. Curt, "In the Blink of an Eye," QST, July 1990 p. 44.Donna Burch, "Morse Code from the Heart," QST July 1990 p. 45. Another example occurred in 1966 when prisoner of war Jeremiah Denton, brought on television by his North Vietnamese captors, Morse-blinked the word TORTURE. In these two cases, interpreters were available to understand those series of eye-blinks.
Morse code is transmitted using just two states (on and off). Historians have called it the first Digital data code. Morse code may be represented as a binary code, and that is what telegraph operators do when transmitting messages. Working from the above ITU definition and further defining a bit as a dot time, a Morse code sequence may be made from a combination of the following five bit-strings:
Note that the marks and gaps alternate: dots and dashes are always separated by one of the gaps, and that the gaps are always separated by a dot or a dash.
Morse messages are generally transmitted by a hand-operated device such as a telegraph key, so there are variations introduced by the skill of the sender and receiver — more experienced operators can send and receive at faster speeds. In addition, individual operators differ slightly, for example, using slightly longer or shorter dashes or gaps, perhaps only for particular characters. This is called their "fist", and experienced operators can recognize specific individuals by it alone. A good operator who sends clearly and is easy to copy is said to have a "good fist". A "poor fist" is a characteristic of sloppy or hard to copy Morse code.
−− −−− ·−· ··· · −·−· −−− −·· · M O R S E C O D E
Next is the exact conventional timing for this phrase, with representing "signal on", and representing "signal off", each for the time length of exactly one dit:
1 2 3 4 5 6 7 812345678901234567890123456789012345678901234567890123456789012345678901234567890123456789 M------ O---------- R------ S---- E C---------- O---------- D------ E
.===...===.===.===...=.===.=...=.=.=...=.......===.=.===.=...===.===.===...===.=.=...^ ^ ^ ^ ^ | dah dit | |symbol space letter space word space
M O R S E C O D E −− −−− ·−· ··· · (space) −·−· −−− −·· ·is orally:
Dah-dah dah-dah-dah di-dah-dit di-di-dit dit, Dah-di-dah-dit dah-dah-dah dah-di-dit dit.
There is little point in learning to read Morse as above; rather, the of all of the letters and symbols need to be learned, for both sending and receiving.
Specifying the dot duration is, however, not the common practice. Usually, speeds are stated in words per minute. That introduces ambiguity because words have different numbers of characters, and characters have different dot lengths. It is not immediately clear how a specific word rate determines the dot duration in milliseconds.
Some method to standardize the transformation of a word rate to a dot duration is useful. A simple way to do this is to choose a dot duration that would send a typical word the desired number of times in one minute. If, for example, the operator wanted a character speed of 13 words per minute, the operator would choose a dot rate that would send the typical word 13 times in exactly one minute.
The typical word thus determines the dot length. It is common to assume that a word is 5 characters long. There are two common typical words: "PARIS" and "CODEX". PARIS mimics a word rate that is typical of natural language words and reflects the benefits of Morse code's shorter code durations for common characters such as "e" and "t". CODEX offers a word rate that is typical of 5-letter code groups (sequences of random letters). Using the word PARIS as a standard, the number of dot units is 50 and a simple calculation shows that the dot length at 20 words per minute is 60 milliseconds. Using the word CODEX with 60 dot units, the dot length at 20 words per minute is 50 milliseconds.
Because Morse code is usually sent by hand, it is unlikely that an operator could be that precise with the dot length, and the individual characteristics and preferences of the operators usually override the standards.
For commercial radiotelegraph licenses in the United States, the Federal Communications Commission specifies tests for Morse code proficiency in words per minute and in code groups per minute.Title 47 Code of Federal Regulations §13.207(c) and Title 47 Code of Federal Regulations §13.209(d) The Commission specifies that a word is 5 characters long. The Commission specifies Morse code test elements at 16 code groups per minute, 20 words per minute, 20 code groups per minute, and 25 words per minute.47 CFR §13.203(b) The word per minute rate would be close to the PARIS standard, and the code groups per minute would be close to the CODEX standard.
While the Federal Communications Commission no longer requires Morse code for amateur radio licenses, the old requirements were similar to the requirements for commercial radiotelegraph licenses.Title 47 Code of Federal Regulations §97.503, 1996 version
A difference between amateur radio licenses and commercial radiotelegraph licenses is that commercial operators must be able to receive code groups of random characters along with plain language text. For each class of license, the code group speed requirement is slower than the plain language text requirement. For example, for the Radiotelegraph Operator License, the examinee must pass a 20 word per minute plain text test and a 16 word per minute code group test.
Based upon a 50 dot duration standard word such as PARIS, the time for one dot duration or one unit can be computed by the formula:
Where: T is the unit time, or dot duration in milliseconds, and W is the speed in wpm.
High-speed telegraphy contests are held; according to the Guinness Book of Records in June 2005 at the International Amateur Radio Union's 6th World Championship in High Speed Telegraphy in Primorsko, Bulgaria, Andrei Bindasov of Belarus transmitted 230 morse code marks of mixed text in one minute.
Using different character and text speeds is, in fact, a common practice, and is used in the Farnsworth method of learning Morse code.
Morse Code, when transmitted, essentially creates an AM signal (even in on/off keying mode), assumptions about signal can be made with respect to similarly timed RTTY signalling. Because Morse code transmissions employ an on-off keying radio signal, it requires less complex transmission equipment than other forms of radio communication.
Morse code also requires less signal bandwidth than voice communication, typically , compared to the roughly 2400 Hz used by single-sideband voice, although at a lower data rate.
Morse code is usually heard at the receiver as a medium-pitched on/off audio tone (600–1000 Hz), so transmissions are easier to copy than voice through the noise on congested frequencies, and it can be used in very high noise / low signal environments. The transmitted power is concentrated into a limited bandwidth so narrow receiver filters can be used to suppress interference from adjacent frequencies. The audio tone is usually created by use of a beat frequency oscillator.
The narrow signal bandwidth also takes advantage of the natural aural selectivity of the human brain, further enhancing weak signal readability. This efficiency makes CW extremely useful for DXing, as well as for low-power transmissions (commonly called "QRP operation", from the Q-code for "reduce power").
The ARRL has a readability standard for robot encoders called ARRL Farnsworth Spacing that is supposed to have higher readability for both robot and human decoders. Some programs like WinMorse have implemented the standard.
Another popular teaching method is the Koch method, named after German psychologist Ludwig Koch, which uses the full target speed from the outset but begins with just two characters. Once strings containing those two characters can be copied with 90% accuracy, an additional character is added, and so on until the full character set is mastered.
In North America, many thousands of individuals have increased their code recognition speed (after initial memorization of the characters) by listening to the regularly scheduled code practice transmissions broadcast by W1AW, the American Radio Relay League's headquarters station.
In the United Kingdom, many people learned the Morse code by means of a series of words or phrases that have the same rhythm as a Morse character. For instance, "Q" in Morse is dah-dah-di-dah, which can be memorized by the phrase "God save the Queen", and the Morse for "F" is di-di-dah-dit, which can be memorized as "Did she like it."
A well-known Morse code rhythm from the Second World War period derives from Beethoven's Fifth Symphony, the opening phrase of which was regularly played at the beginning of BBC broadcasts. The timing of the notes corresponds to the Morse for "V", di-di-di-dah, understood as "V for Victory" (as well as the Roman numeral for the number five).Glenn Stanley, The Cambridge Companion to Beethoven, p.269, Cambridge University Press, 2000 .William Emmett Studwell, The Americana Song Reader, p.62, Routledge, 1997 .
|Ö, ö |
Shared by Ó, Ö, Ø
There is no standard representation for the exclamation mark (!), although the KW digraph () was proposed in the 1980s by the Heathkit Company (a vendor of assembly kits for amateur radio equipment).
While Morse code translation software prefers the Heathkit version, on-air use is not yet universal as some amateur radio operators in North America and the Caribbean continue to prefer the older MN digraph () carried over from American landline telegraphy code.